10-19-2016, 10:13 AM | #89 |
First Lieutenant
115
Rep 324
Posts |
|
Appreciate
1
ClothSeats341.00 |
10-19-2016, 10:16 AM | #90 |
Second Lieutenant
144
Rep 216
Posts
Drives: 2017 BMW M2
Join Date: Dec 2011
Location: Fort Worth, Tx
|
The door seals cut down on some of road noise that gets in the cabin from front tire area. It's 228i part that fits in the open space between the inside of the fender and door frame in front of the door hinges.
__________________
2016 750i X-drive
2017 GMC Sierra Denali 1997 MB SL500, 19"AMG replicas Past BMWs: E30 323i, E36 325is, E36 M3, E46 M3, E39 M5, E46 325i, E90 335i, F80 M3, F87 M2 |
Appreciate
2
ClothSeats341.00 bollinm25.00 |
10-21-2016, 01:15 AM | #91 |
Queen of Motorsports
235
Rep 282
Posts
Drives: BMW 2016 M2
Join Date: May 2016
Location: New York
|
Brake cover for about $25. You can get anything you want. I just got another one that says Rogue.
__________________
Instagram @winterrogue_F87
Tai Winter Targaryen |
Appreciate
4
|
10-21-2016, 07:32 AM | #92 |
Major General
4449
Rep 7,594
Posts
Drives: '19 M2C
Join Date: Jun 2007
Location: Chicagoland
|
Which turn signal bulbs did you buy? Any video of what they look like?
__________________
www.ReTuneTheDeTune.com
2019 M2 Competition (Sunset Orange) |
Appreciate
0
|
10-21-2016, 09:52 AM | #93 |
First Lieutenant
354
Rep 365
Posts |
I also posted this in another section of this board.... but it fits well here too;
To hard wire your radar detector or dash cam you can easily and inexpensively tap into the mirror housing. I have a dash cam in both our 2012 535I and 2016 M2 and also hard wired a V1 radar detector in the 535 mounted with a Blendmount. On the 535I I tapped into the mirror for power on one and the overhead console for the power on the other. The mirror is much much easier. I used shawnsheridan posting on another forum to install the F10s. When I opened the rear view mirror's housing on the M2 (very easy) I found the same the 10-Wire Connector Plug inside it. The +12V (Switched off the ignition) on the Brown/Green wire and Ground on the Brown/Black wire. I used the wire taps and fed the wire at the top of the mirror housing. Good to go.
__________________
2022 X5 40I - Ours
2016 BMW M2 LBB 6 Sp / ED Pick Up on 07/12/2016 - Her's 1995 Porsche 993 Cab - Mine 2001 Toyota Tundra SR5 Ext Cab - Hay Hauler |
Appreciate
5
|
10-22-2016, 01:57 AM | #94 |
Major
281
Rep 1,017
Posts |
|
Appreciate
0
|
10-22-2016, 03:35 AM | #95 | |
Queen of Motorsports
235
Rep 282
Posts
Drives: BMW 2016 M2
Join Date: May 2016
Location: New York
|
Quote:
__________________
Instagram @winterrogue_F87
Tai Winter Targaryen |
|
Appreciate
1
Smiley1175281.00 |
10-24-2016, 03:20 PM | #96 |
Registered
5
Rep 1
Posts |
M2 Charity Giveaway
We're doing a BMW M2 giveaway for charity, and thought you guys might be interested? You can see more about the giveaway here – http://crowdrise.com/bmwm2 It was hand painted by street artist Greg Mike, and it is such a beauty – holy crap! |
11-07-2016, 06:20 AM | #97 |
Second Lieutenant
325
Rep 240
Posts |
This thread appears to have lost steam when everyone witnessed the unholy thing done to that poor AW in the name of charity... Try to get past that and keep the light mods/hacks coming. This has been one of my favorite threads to follow, I have already ordered many of these bits for my MG one month away.
Can't wait!!
__________________
'02 E39 M5-Gone
'07 E60 M5-Gone '07 E64 M6 Cab-Gone '17 F87 MG M2-Gone '19 F87 SO M2C |
Appreciate
0
|
11-07-2016, 08:53 AM | #98 |
Major
652
Rep 1,406
Posts
Drives: 2020 SO - M2C
Join Date: Dec 2010
Location: KOP, PA
|
|
Appreciate
0
|
08-29-2018, 08:49 PM | #99 |
Captain
503
Rep 780
Posts |
Old Tread....but never too late.
$15/ rattle can of LLB and Clear. Sanded and sprayed the front reflectors. Used a roll of 3M automotive butyl to stick them back in. Looks just like an IND bought one but cost $130 less.... and was way more satisfying!
__________________
"I would rather cry in a BMW than smile on a bicycle." Ma Nuo |
Appreciate
9
QM287.00 akkando5863.00 $M271.50 mssVT98141.50 bollinm25.00 gphung193.50 CosmosMpower2050.50 Kankles1484.50 cactusjack370.50 |
08-29-2018, 11:26 PM | #100 |
Private First Class
61
Rep 130
Posts |
the BMS clutch stop is not good for clutch, your clutch is not fully disengaged when using, there are some reports of it ruining peoples cars if you search google
|
Appreciate
0
|
08-30-2018, 02:34 AM | #101 |
New Member
28
Rep 24
Posts |
|
Appreciate
0
|
08-30-2018, 07:04 AM | #102 | |
First Lieutenant
260
Rep 370
Posts |
Quote:
I've been driving with this for nearly 2 years and haven't had any issues. Clutch feels completely disengaged to me.
__________________
'01 M Roadster, '24 BSM M2
|
|
Appreciate
2
DrKevM52269.00 eatingpizzainthef87rules253.00 |
08-30-2018, 08:49 AM | #103 |
Lieutenant
1184
Rep 571
Posts |
I haven't installed it, but plan to and I'd like to see those same reports. I ran three different Google searches, "BMS clutch stop problems", "BMS clutch stop ruined car" and "BMS clutch stop ruined clutch" and I found absolutely nothing, not even a single negative article or forum post. If there are reasons not to install this, I'd appreciate seeing whatever info people are looking at because everything I'm seeing is positive.
|
Appreciate
1
bluescoupe57.00 |
08-30-2018, 10:23 AM | #104 | |
Private First Class
142
Rep 183
Posts |
Quote:
Thanks! |
|
Appreciate
0
|
08-30-2018, 04:26 PM | #105 | |
Captain
503
Rep 780
Posts |
Quote:
Once off: Cleaned the butyl off the car and the reflectors. Used lighter fluid and a scraper. Sanded the reflector top and sides with 180 grit sandpaper. This included sanding off the raised graphic on the reflector. Masked the non reflective area as I used the 3m "butyl on that later. See my pics. Sprayed 2 costs of plastic "adhesive enhancer", make sure you hit the sides of the reflectors. Sanded with 1000 grit. Spayed 2 coats of sanding primer (this step is not required some say) Lightly sand with wet 1000 grit. washed and dried with a hair dryer. 3 Coats of car body color. Wet 1000 before last coat. 3 coats of clear. Sand between required. I didn't. Apply the 3M 1/32 thick butyl product and trim then stick back on the car. As the clear coat will be soft for a few days watch for finger prints while install the adhesive material. All the above can be bought from any online or local automotive paint supplier. Amazon sell kits but they are expensive compared to local guys. Moulding tape: https://www.3m.com/3M/en_US/company-...3241071&rt=rud Hope this helps!
__________________
"I would rather cry in a BMW than smile on a bicycle." Ma Nuo |
|
Appreciate
1
failuretothrive18.50 |
09-02-2018, 11:39 PM | #107 | |
BMW Fanaddict
65
Rep 76
Posts |
Quote:
|
|
Appreciate
0
|
09-03-2018, 11:49 AM | #109 | |
Lieutenant
1184
Rep 571
Posts |
Quote:
https://f87.bimmerpost.com/forums/sh...1260588&page=8 |
|
Appreciate
0
|
09-05-2018, 01:34 PM | #110 |
Captain
480
Rep 756
Posts
Drives: M2
Join Date: Nov 2016
Location: PNW
|
Me too, thanks for the info!
__________________
'17 M2 DCT Long Beach Blue
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|