05-12-2019, 01:07 AM | #1 |
Colonel
1860
Rep 2,104
Posts |
AutoSolutions M2 Comp Short Shift Kit Quick Review
I haven't seen too many of these installed on the M2, so I thought I'd give a quick review. AutoSolutions is generally known to have made the best SSK for the E46 M3, and probably the best SSK's in general short of (pun intended) something like CAE. The owner, Ron, has an amazing knowledge base and understanding of BMW shifters. I went back and forth with Ron for months, and he finally agreed to make me a SSK for the M2 Comp (but should fit the OG M2 as well). Mine was a bit custom in the throws, feel, and length. I wanted something with noticeably shorter throws and minimal increase in shifting effort. Ron analyzed the weakest parts of BMW's current shifter design, and only replaced the parts that he felt made a significant difference.
I had considered doing the install myself, but so glad I didn't. Performance Technic did the install, and they had to remove the plastic covers, multiple heat shields, and the exhaust; and partially move/drop the transmission and driveshaft. They did an excellent job. Due to the parts this kit replaces, the install is not possible from the top. The OEM components feel cheap and flimsy in comparison, even though they are not. OEM: The good stuff: So how is it? I didn't think BMW's current shifter was too bad, especially compared to older BMW's, that had almost an inch of play while IN GEAR. However, the AutoSolutions SSK makes the OEM one feel mushy and vague. The shifts are extremely solid, precise, and crisp; they feel almost magnetic. There is definitely more connection with the car; everything just feels so much more direct. I did notice a slight increase in engine noise, but I view that as a positive; you have more communication with the car. There is not a noticeable increase in vibrations. This does not feel like an evolutionary improvement of the OEM shifter; it feels completely different, almost revolutionary. It seems even better when you shift fast. I feel like a race car driver I have no problems with the auto-rev-matching. Everything works smoothly. There is a slight increase in shift effort required. But very importantly, it is very easy to shift into first. I already liked the M2 a lot; this makes me like it a lot more. A quick vid of the shorter throws: One important thing worth mentioning is that it sits completely centered, the same as OEM, when in neutral. Previous kits for F-series cars from other manufacturers had problems with the shifter not resting properly in neutral, or the knob being twisted. This kit has none of those issues. Last edited by RocketBoots; 05-13-2019 at 01:24 PM.. |
Appreciate
12
Shaunhmc9.50 Threeebowel31.50 newnmpr0ved86.00 hexximus4.50 wellvrsd72.00 Poochie9104.50 SYT_Shadow11479.50 chief1richard381.00 6speed_M23633.50 BMW DIY Guy3070.00 Childish3.50 Altra265.50 |
05-14-2019, 02:13 AM | #5 |
Lieutenant
437
Rep 553
Posts |
Good to hear you're happy with it, my Auto Solutions kit arrived last week & being installed in a couple of days. Expect my only regret will be that I didn't do it sooner. Last edited by David.m; 05-14-2019 at 07:05 AM.. |
Appreciate
0
|
05-14-2019, 07:09 AM | #6 |
Lieutenant
437
Rep 553
Posts |
Link to Auto Solutions website here http://www.autosolutions.net
F8X series aren't mentioned on the website but he has done many I believe, email Ronald and you will get very a detailed and informative response. |
Appreciate
1
_tphamm199.00 |
05-14-2019, 10:57 AM | #7 |
Major
1123
Rep 1,083
Posts |
I had my Autosolutions SSK installed over the weekend as well. It seems that as it warms up, it will become more sticky (see video). I had it installed with the rear PU shifter bushing from Turner, but my kit didn't come with the blue bushings in your picture. I wonder if there's different kits from Ron. Cheers, Sunny
__________________
|
Appreciate
1
gandapanda55.50 |
05-14-2019, 06:20 PM | #8 | |
Captain
319
Rep 660
Posts |
Quote:
|
|
Appreciate
0
|
05-14-2019, 08:29 PM | #9 | |
Lieutenant
437
Rep 553
Posts |
Quote:
|
|
Appreciate
0
|
05-14-2019, 10:29 PM | #10 |
Colonel
1860
Rep 2,104
Posts |
As David.m linked, that's the site; unfortunately, it isn't very updated, but does contain a lot of info on shifter design. I think he spends all his time on the shifters instead of web pages, lol. Ron's done a decent amount of F80/F82 kits. You'll have to email/call him about the M2 kit.
ashtaron14 That seems very odd. Definitely shoot Ron an email. I think you may have gotten a longer throw than me (not that it matters). Is it just the camera angle, or is your shift knob twisted a bit?? Also, what rear bushing did you replace?? I didn't replace anything other than what was in the kit. The blue bushings are upgraded urethane bushings; I believe he was using OEM bushings before. Ron said there are always tradeoffs, but thinks he found the right magic formula. I have no complaints |
Appreciate
1
fixa1.50 |
05-15-2019, 02:30 AM | #11 | |
Major
1123
Rep 1,083
Posts |
Quote:
I replaced this bushing. I specifically asked Ron to make me a SSK that retains the stock height of the shift knob, so yeah it could be a longer throw. My shift knob isn't twisted but my car is a RHD so it could well be the angle of my video. I've emailed Ron with my video & explanation, and will see how he responds.
__________________
|
|
Appreciate
0
|
05-15-2019, 09:17 AM | #12 | |
Colonel
1860
Rep 2,104
Posts |
Quote:
|
|
Appreciate
0
|
05-15-2019, 09:42 AM | #13 | |
Major
1123
Rep 1,083
Posts |
Quote:
As to why I chose to replace it, I guess Turner's explanation was convincing that it's a weak link, and the OEM piece is quite flimsy.
__________________
|
|
Appreciate
0
|
05-16-2019, 11:34 AM | #14 |
Private First Class
102
Rep 112
Posts |
That's a really nice short shift kit. I had one in my last two cars and love them. Was curious about these for the M2C, and now I'll have to look really hard at getting one.
__________________
|
Appreciate
0
|
05-16-2019, 11:36 AM | #15 | |
Private First Class
102
Rep 112
Posts |
Quote:
__________________
|
|
Appreciate
0
|
05-19-2019, 10:19 AM | #16 |
Major
1123
Rep 1,083
Posts |
It's the F10 M5 Shift Knob modded to fit onto the M2C, but you lose the blue/orange stitching while gaining the light.
__________________
|
05-19-2019, 02:09 PM | #17 |
Major General
1545
Rep 8,970
Posts |
OP, thanks to your posts I'm in discussion with Ron this week.
He is running a batch of M2 shifter's this week. I'm going for 10mm shorter and 20% movement reduction. He includes poly bushes for $40 which I'm having. RHD shifters do look twisted towards left driver side. My factory and m perf shifters are ever so slightly twisted. What a great guy he is, never had such in depth discussion with a shop before! Last edited by doughboy; 05-19-2019 at 02:18 PM.. |
Appreciate
0
|
05-19-2019, 02:20 PM | #18 |
Major General
1545
Rep 8,970
Posts |
Ron advised that the f10 M5 knob is 13mm shorter than OE M2 knob, so he said don't go for reduced shifter height if fitting shorter knob as well.
|
Appreciate
0
|
05-19-2019, 08:13 PM | #19 | |
Major
1123
Rep 1,083
Posts |
Quote:
__________________
|
|
Appreciate
0
|
05-23-2019, 12:45 PM | #20 | |
Colonel
1860
Rep 2,104
Posts |
Good to hear! Ron said he's been working on finding the magic formula for those bushings, and after years, thinks this is the one. It's incredible how much thought goes into these little details, and how much of a tangible difference it can make.
I actually do not remember the % reduction in my throws, but to me, the firm, crisp action was more notable. So damn crispy! Be warned, it will feel like a greater shifting effort at first, especially with your shorter length. I adjusted to mine in about a day. Quote:
|
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|