BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read
M2 Technical Topics > S55 Engine / Drivetrain / Exhaust / Bolt-ons / Tuning > M2C missing part of intake piping.

Post Reply
 
Thread Tools Search this Thread
      02-05-2020, 04:12 AM   #67
Commanderwiggin
Captain
Commanderwiggin's Avatar
United_States
716
Rep
637
Posts

Drives: 19 M2C;12 X5 35D;Turbo E46 M3
Join Date: Mar 2014
Location: Socal

iTrader: (0)

Quote:
Originally Posted by Conissah View Post
I am somewhat handy with my 3d printer and subsequent programs. Might try and get some measurements and whip something up.
Did you ever whip something up?
__________________
575RWHP F87 M2C - ECUTEK RACEROM with flex fuel tuning by Bend Calibration
1000+RWHP E46 M3, Lab22 Built Turbo S54, Bend Calibration Tuned - BMW Half Mile Record Holder
Appreciate 1
Conissah891.50

      02-05-2020, 08:23 AM   #68
Conissah
Captain
Conissah's Avatar
892
Rep
796
Posts

Drives: 2020 BMW M2C
Join Date: Oct 2019
Location: Charlotte, NC

iTrader: (0)

Quote:
Originally Posted by Commanderwiggin View Post
Did you ever whip something up?
I did not, haven't had much spare time, and the little I do goes towards working on my Miata. I'll get around to it, eventually.
Appreciate 1
      02-05-2020, 07:08 PM   #69
msdss
Lieutenant
msdss's Avatar
United_States
168
Rep
406
Posts

Drives: Alpine White 2020 BMW M2C
Join Date: May 2015
Location: United States

iTrader: (0)

Has anyone heard anything back from Imran@Evolve ?
Earlier in the thread, someone mentioned Evolve was going to create a solution for this.
Appreciate 0
      02-11-2020, 12:31 PM   #70
Commanderwiggin
Captain
Commanderwiggin's Avatar
United_States
716
Rep
637
Posts

Drives: 19 M2C;12 X5 35D;Turbo E46 M3
Join Date: Mar 2014
Location: Socal

iTrader: (0)

Did anyone ever try fitting the elbows from the M3/M4? I read all the posts earlier...just curious if anyone tried.
__________________
575RWHP F87 M2C - ECUTEK RACEROM with flex fuel tuning by Bend Calibration
1000+RWHP E46 M3, Lab22 Built Turbo S54, Bend Calibration Tuned - BMW Half Mile Record Holder
Appreciate 0
      02-11-2020, 02:41 PM   #71
Commanderwiggin
Captain
Commanderwiggin's Avatar
United_States
716
Rep
637
Posts

Drives: 19 M2C;12 X5 35D;Turbo E46 M3
Join Date: Mar 2014
Location: Socal

iTrader: (0)

I contacted Eventuri and they mentioned April for the fresh air intake on the M2C.
__________________
575RWHP F87 M2C - ECUTEK RACEROM with flex fuel tuning by Bend Calibration
1000+RWHP E46 M3, Lab22 Built Turbo S54, Bend Calibration Tuned - BMW Half Mile Record Holder
Appreciate 3
Alfy58.50
msdss168.00

      03-04-2020, 07:36 PM   #72
msdss
Lieutenant
msdss's Avatar
United_States
168
Rep
406
Posts

Drives: Alpine White 2020 BMW M2C
Join Date: May 2015
Location: United States

iTrader: (0)

I spoke to Eventuri yesterday and the said they aren't doing anything about this at all, and have had no plans to do anything ever.

they went as far as saying to modify my car and fit the m4 ducts if I wanted a solution.

Soo....
Appreciate 0
      03-04-2020, 09:31 PM   #73
Malakas
First Lieutenant
United_States
143
Rep
363
Posts

Drives: 2020 M2c
Join Date: Jun 2011
Location: Houston, TX

iTrader: (0)

I've got something on the 3d printer cooked up and flow tested in computer simulation....

I ordered some stock intake pieces to make sure the specs are right and will likely be able to mock it up next week. Will report back here when it's done and tested. Will be hapoy to share if anyone is interested.
Appreciate 6
      03-05-2020, 06:20 PM   #74
Project_F87
Lieutenant
Project_F87's Avatar
United_States
387
Rep
575
Posts

Drives: 2020 M2C LBB 6MT
Join Date: Apr 2017
Location: Palmdale, CA

iTrader: (0)

Quote:
Originally Posted by Malakas View Post
I've got something on the 3d printer cooked up and flow tested in computer simulation....

I ordered some stock intake pieces to make sure the specs are right and will likely be able to mock it up next week. Will report back here when it's done and tested. Will be hapoy to share if anyone is interested.
Awesome! Share the CAD files for us peeps with 3D printers please?
__________________
Instagram: @project_f87
Appreciate 0
      03-05-2020, 08:24 PM   #75
Malakas
First Lieutenant
United_States
143
Rep
363
Posts

Drives: 2020 M2c
Join Date: Jun 2011
Location: Houston, TX

iTrader: (0)

Quote:
Originally Posted by Project_F87 View Post
Awesome! Share the CAD files for us peeps with 3D printers please?
Will do. I have so many different versions as of now... I have the oem intake pieces coming in any day to test fit. Once I have a final version that fits nicely, will post up the files.
__________________
Ride: 2020 F87 M2C, 6MT Drive: Nine-Four Motorsports
Before:
2013 - 3.8L GTR, first DCT
2012 - 5.2L R8 v10, 6MT
2011 - 4.0L E92 M3, 6MT
Appreciate 4
      03-05-2020, 10:24 PM   #76
Commanderwiggin
Captain
Commanderwiggin's Avatar
United_States
716
Rep
637
Posts

Drives: 19 M2C;12 X5 35D;Turbo E46 M3
Join Date: Mar 2014
Location: Socal

iTrader: (0)

Quote:
Originally Posted by Malakas View Post
Will do. I have so many different versions as of now... I have the oem intake pieces coming in any day to test fit. Once I have a final version that fits nicely, will post up the files.
That's awesome! Eagerly waiting to see how all this works out!
__________________
575RWHP F87 M2C - ECUTEK RACEROM with flex fuel tuning by Bend Calibration
1000+RWHP E46 M3, Lab22 Built Turbo S54, Bend Calibration Tuned - BMW Half Mile Record Holder
Appreciate 1
Alfy58.50

      03-12-2020, 07:33 AM   #77
Carbon_73
New Member
Russia
23
Rep
24
Posts

Drives: M2 Competition
Join Date: Jul 2017
Location: Kazan

iTrader: (0)

Hi, everyone.
I installed corner pipes (13717613156, 13717613157) and meshes (13718507321) from the M3/M4 on my M2C. Everything works perfectly!
Attached Images
  
Appreciate 3
Alfy58.50
Poochie4058.50

      03-12-2020, 08:07 AM   #78
flybigjet
Remove Before Flight
flybigjet's Avatar
United_States
793
Rep
453
Posts

Drives: a light twin from Boeing.
Join Date: Dec 2019
Location: Denver, CO

iTrader: (0)

Quote:
Originally Posted by Carbon_73 View Post
Hi, everyone.
I installed corner pipes (13717613156, 13717613157) and meshes (13718507321) from the M3/M4 on my M2C. Everything works perfectly!
Confused.

Is this just a bolt-on with four parts, or is there 3D printing parts involved??
Appreciate 0
      03-12-2020, 08:18 AM   #79
Bee Pee
Brigadier General
United Kingdom
1249
Rep
3,979
Posts

Drives: AW M2 DCT
Join Date: Jun 2010
Location: SW London

iTrader: (3)

Quote:
Originally Posted by flybigjet View Post
Confused.

Is this just a bolt-on with four parts, or is there 3D printing parts involved??
4 oem s55 m3/4 parts pnp - LHS elbow + RHS elbow + 2 x meshes - part no as per post above.

If wanting a scoop - some folks modify a gauge pod to make a scoop mounted front-wards over the mesh....

https://www.amazon.co.uk/BODYART-Uni.../dp/B075LNFRJ4
__________________
Fettled M135i EB AT - gone but not forgotten:
AW M2 DCT
Appreciate 2
Poochie4058.50

      03-12-2020, 10:03 AM   #80
Carbon_73
New Member
Russia
23
Rep
24
Posts

Drives: M2 Competition
Join Date: Jul 2017
Location: Kazan

iTrader: (0)

Quote:
Originally Posted by flybigjet View Post
Confused.

Is this just a bolt-on with four parts, or is there 3D printing parts involved??
These are fully factory-made parts from M3/M4. Everything is installed without problems! You only need to cut holes in the plastic.
Without 3D ))))
Appreciate 2
      03-12-2020, 10:07 AM   #81
Carbon_73
New Member
Russia
23
Rep
24
Posts

Drives: M2 Competition
Join Date: Jul 2017
Location: Kazan

iTrader: (0)

I apologize for the bad photos, but I couldn't take a better picture.
Attached Images
        
Appreciate 3
Poochie4058.50
CSBM51348.00

      03-12-2020, 02:47 PM   #82
Malakas
First Lieutenant
United_States
143
Rep
363
Posts

Drives: 2020 M2c
Join Date: Jun 2011
Location: Houston, TX

iTrader: (0)

That looks awesome.

I redesigned the elbow and included a ram air scoop. Also I tried to move it a bit forward .... Prototype 1 was tested, but there were some issues ... So on to prototype 2.

I've been luck enough to consult with some pro mechanics via a friend and discuss airflow velocities etc... Will present my findings here once completed.

Last edited by Malakas; 03-12-2020 at 03:01 PM..
Appreciate 2
      03-12-2020, 03:36 PM   #83
flybigjet
Remove Before Flight
flybigjet's Avatar
United_States
793
Rep
453
Posts

Drives: a light twin from Boeing.
Join Date: Dec 2019
Location: Denver, CO

iTrader: (0)

Quote:
Originally Posted by Carbon_73 View Post
These are fully factory-made parts from M3/M4. Everything is installed without problems! You only need to cut holes in the plastic.
Without 3D ))))
How does the elbow connect to the part where you cut the plastic?

And I *think* there are templates stamped into the plastic for where to cut?

TIA--

R.
Appreciate 0
      03-12-2020, 05:56 PM   #84
speedsnice
Private First Class
269
Rep
162
Posts

Drives: 1999 BMW M3, 2020 M2 Comp
Join Date: May 2019
Location: Westchester New York

iTrader: (0)

I will have to add this to the mod list.
__________________
1999 M3 Convertible manual
2018 Subaru Crosstrek Limited (commuter car)
2020 M2 Competition

Instagram @s55m2
Appreciate 0
      03-13-2020, 03:43 AM   #85
Carbon_73
New Member
Russia
23
Rep
24
Posts

Drives: M2 Competition
Join Date: Jul 2017
Location: Kazan

iTrader: (0)

Quote:
Originally Posted by flybigjet View Post
How does the elbow connect to the part where you cut the plastic?

And I *think* there are templates stamped into the plastic for where to cut?

TIA--

R.
The photo shows how the angle pipe is inserted into the plastic from the inside. It holds perfectly, and is fixed on the outside with a grid.

The template is a corner pipe!

Very simple installation, no need to invent anything ! All OEM.
Attached Images
  
Appreciate 0
      03-13-2020, 03:44 AM   #86
Carbon_73
New Member
Russia
23
Rep
24
Posts

Drives: M2 Competition
Join Date: Jul 2017
Location: Kazan

iTrader: (0)

Quote:
Originally Posted by speedsnice View Post
I will have to add this to the mod list.
Appreciate 1
      03-13-2020, 04:54 AM   #87
Commanderwiggin
Captain
Commanderwiggin's Avatar
United_States
716
Rep
637
Posts

Drives: 19 M2C;12 X5 35D;Turbo E46 M3
Join Date: Mar 2014
Location: Socal

iTrader: (0)

Carbon_73 what all did you remove to do the install/cutting properly? Looks like front bumper and possibly the headlights?
__________________
575RWHP F87 M2C - ECUTEK RACEROM with flex fuel tuning by Bend Calibration
1000+RWHP E46 M3, Lab22 Built Turbo S54, Bend Calibration Tuned - BMW Half Mile Record Holder
Appreciate 0
      03-13-2020, 05:49 AM   #88
Carbon_73
New Member
Russia
23
Rep
24
Posts

Drives: M2 Competition
Join Date: Jul 2017
Location: Kazan

iTrader: (0)

Quote:
Originally Posted by Commanderwiggin View Post
Carbon_73 what all did you remove to do the install/cutting properly? Looks like front bumper and possibly the headlights?
No changes! Looks like from the factory : Thumsup:
Attached Images
 
Appreciate 1
Poochie4058.50

Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 01:33 AM.




m2
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST