BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read
BMW M2 Forum > M2 Photos, Videos and Builds > Tano's LBB M2 LCI

Post Reply
 
Thread Tools Search this Thread
      10-11-2019, 02:06 AM   #177
Tano
First Lieutenant
Tano's Avatar
Hungary
248
Rep
323
Posts

Drives: BMW M2
Join Date: Oct 2015
Location: Hungary

iTrader: (0)

So here is the comparison between Stock map and St2 93OCT v5.8 map. Disregarding the right edge which is wrong data i think, at 5800 the difference is 381 vs 417 hp. Its quite consistent 30-ish hp difference at the higher RPM range and much better at lower RPM.
Attached Images
 
__________________
Appreciate 0
      10-26-2019, 03:38 PM   #178
Tano
First Lieutenant
Tano's Avatar
Hungary
248
Rep
323
Posts

Drives: BMW M2
Join Date: Oct 2015
Location: Hungary

iTrader: (0)

On 23rd we had a national holiday so i could go to the last trakday of this season on the Pannonia Ring. It was a busy day, the first 3 session was interrupted with red flags due to off tracks and mechanical failures. In the 3rd session a Subaru Impreza went off track while i was following it so i managed to record it. Only the 4th session went without interruption although there were 2 spins in front of me again.
Previously i installed the Porsche GT3 brake cooling scoops to the front axle too because i wasn't satisfied with the ducts. They were rubbing. So my experience is positive with the scoops. Although the air temp was 10C colder than summer time but after a 30 minute session with 1 cooling lap my disc temp was only 230 C and caliper temp was about 150-170C which is significantly lower than without extra cooling like i posted previously.
And here are my videos from this event. Now i made records with my phone's camera too and created PIP videos.

__________________
Appreciate 0
      11-03-2019, 03:49 PM   #179
Tano
First Lieutenant
Tano's Avatar
Hungary
248
Rep
323
Posts

Drives: BMW M2
Join Date: Oct 2015
Location: Hungary

iTrader: (0)

My track package.
Attached Images
 
__________________
Appreciate 1
Anthony1s920.00

      11-16-2019, 12:00 PM   #180
Tano
First Lieutenant
Tano's Avatar
Hungary
248
Rep
323
Posts

Drives: BMW M2
Join Date: Oct 2015
Location: Hungary

iTrader: (0)

Winter is coming, so today I installed The Automotive Passion's CF Arch guards. They look neat, I like them!
Attached Images
  
__________________
Appreciate 0
      12-08-2019, 04:23 PM   #181
Tano
First Lieutenant
Tano's Avatar
Hungary
248
Rep
323
Posts

Drives: BMW M2
Join Date: Oct 2015
Location: Hungary

iTrader: (0)

Another winter preparation is the rubber M-Performance floor mats.
Attached Images
  
__________________
Appreciate 0
      12-10-2019, 10:46 AM   #182
Anthony1s
Major
920
Rep
1,435
Posts

Drives: 2018 Mineral Grey M2
Join Date: Oct 2017
Location: Pennsylvania

iTrader: (0)

Quote:
Originally Posted by Tano View Post
My track package.
Do you use that bike pump for your tires? Why not use the air compressor the M2 comes with? It's a smaller item and works well.
__________________
Click "Appreciate" on my post if I was helpful. Thanks!
Appreciate 0
      12-11-2019, 02:52 PM   #183
Tano
First Lieutenant
Tano's Avatar
Hungary
248
Rep
323
Posts

Drives: BMW M2
Join Date: Oct 2015
Location: Hungary

iTrader: (0)

Quote:
Originally Posted by Anthony1s View Post
Do you use that bike pump for your tires? Why not use the air compressor the M2 comes with? It's a smaller item and works well.
It depends, sometimes i use that too. However the hand pump a bit faster and less hassle.
__________________
Appreciate 1
Anthony1s920.00

      12-12-2019, 02:16 PM   #184
chief1richard
Racing is Life anything in between is just waiting
chief1richard's Avatar
United_States
166
Rep
405
Posts

Drives: At the point of 7,000 RPM's
Join Date: May 2017
Location: Boston

iTrader: (0)

Camber Plates

Quote:
Originally Posted by Tano View Post
It depends, sometimes i use that too. However the hand pump a bit faster and less hassle.
Was wondering if you have any noise or vibrations after your Camber Plate install ? Did you keep your OEM Springs ? What, if any difference on Public Roads ? Am considering Camber Plates for my M2.
__________________
At a Point above 7,000 RPM.
Appreciate 0
      12-13-2019, 08:11 AM   #185
Tano
First Lieutenant
Tano's Avatar
Hungary
248
Rep
323
Posts

Drives: BMW M2
Join Date: Oct 2015
Location: Hungary

iTrader: (0)

Quote:
Originally Posted by chief1richard View Post
Was wondering if you have any noise or vibrations after your Camber Plate install ? Did you keep your OEM Springs ? What, if any difference on Public Roads ? Am considering Camber Plates for my M2.
Yes i kept the OEM strut, i changed only the top mount plate. There is no vibration, only a bit noisier on rough roads (which we have plenty in Hungary ) but not annoying level at all. During daily driving there is not much difference since it's not pushed to the limits, but it's definitely better on the track.
__________________
Appreciate 1
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 10:13 PM.




m2
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST