03-06-2023, 10:28 PM | #1 |
Private
69
Rep 81
Posts |
Question: DSC and coding
I threw a cage, seats and 6 points in the car. It's a track only car. I haven't had the usual stuff coded out yet (airbag seat occupancy sensors, seatbelt warning lights, etc). I have an event this weekend and not sure I can get it coded in time. Can I run the car with DSC off or will it try to kick the nannies back on like when TPMS shows low pressure? Just wondering how urgently I should be hunting down a coder.
|
03-07-2023, 06:41 AM | #2 |
Coffee Every Day
397
Rep 359
Posts
Drives: 2021 M2C
Join Date: Jun 2018
Location: South Korea
|
Atleast in my experience it should be fine. I usually code it on and off when i put the pssenger seat back in but have had it with warnings on for like 10 track days since i no longer have the passenger seat in
Also accidently cut some airbag harness cables lol. Even with a cut harness and ectra warnings….Ran fine last weekend in MDM and DSC off as far as i could tell.
__________________
-2021 M2C, HS, 6MT
-AST 5100, AP Racing 9660, BMW-788M, RF-GT4, BW-TA5R, APR GT 250 Wing & Front Splitter -TMS Diffuser, TMS F80 Skid Plate, HEX Armor PPF, CAN-Checked Data Logger, RaceBox -Recaro Pole Position , 2kBody Half Cage, Pinnacle Motorsports Half Cage (On order), CAE Shifter -Remus Race + BR EL Mid |
Appreciate
1
Hawkdriver68.50 |
03-07-2023, 11:40 AM | #3 |
Lieutenant
518
Rep 582
Posts |
Based on my experience with my 2017, the car will turn into comfort mode with the nannies on if you let the TPMS read the pressures below a certain threshold, typically below around 28lbs. This is higher than what ideally you may want to start the day on. So you have three options:
1. Work with the setup you currently have and manage pressures throughout the day. Start above 28lbs and bleed out air in between sessions as needed to keep hot pressures where you want then. Add air in if the car has been sitting for a while and pressures drop. Doing this will enable you to run with everything off. 2. Take out the TPMS sensors. This will let you run in any mode without having to spend effort managing the systems. Albeit, you will have a light on the dash indicating a TPMS error. 3. Code out the TPMS
__________________
2017 BMW M2 5Spd, 2007 VW Touareg, 2023 Yamaha MT09 SP
https://www.instagram.com/dvas99/ https://www.youtube.com/channel/UC2j..._as=subscriber |
Appreciate
1
Hawkdriver68.50 |
03-07-2023, 03:10 PM | #4 |
Private
69
Rep 81
Posts |
dvas Thanks bud, but that wasn't my question. I am aware of the TPMS. I already have that coded out because of all the sets of wheels and tires I use. I was asking about the airbag and sealbelt issues when seats are replaced. Do you know if I can run the car full DCS off with it kicking UT back into comfort mode with the airbag and seat warnings?
|
Appreciate
0
|
03-07-2023, 04:10 PM | #5 | |
M2 From Down Under
85
Rep 33
Posts |
Quote:
|
|
Appreciate
1
Hawkdriver68.50 |
03-07-2023, 07:51 PM | #6 | |
Lieutenant
518
Rep 582
Posts |
Quote:
__________________
2017 BMW M2 5Spd, 2007 VW Touareg, 2023 Yamaha MT09 SP
https://www.instagram.com/dvas99/ https://www.youtube.com/channel/UC2j..._as=subscriber |
|
Appreciate
1
Hawkdriver68.50 |
03-08-2023, 01:30 PM | #7 | |
Brigadier General
4016
Rep 3,540
Posts
Drives: 328d Wagon, M2 Comp, i4 eD35
Join Date: Sep 2016
Location: Bay Area, CA
|
Quote:
__________________
-328d Wagon Build Log (with helpful reference links)
-My YouTube Channel for some of the best DIYs and in depth information Please don't PM me for suspension recommendations unless interested in paid private consultations. |
|
Appreciate
0
|
03-08-2023, 08:12 PM | #8 |
Private
69
Rep 81
Posts |
|
Appreciate
0
|
03-11-2023, 02:53 AM | #9 | |
Coffee Every Day
397
Rep 359
Posts
Drives: 2021 M2C
Join Date: Jun 2018
Location: South Korea
|
Quote:
[*] set the following codes from aktiv to nicht_aktiv:[/LIST] CIS_Beifaher (Occupancy sensor) Sitzairbag_Thorax_Fahrer (Driver seat airbag) Sitzairbag_Thorax_Beifahrer (Passenger seat airbag) Sitzpositionsensor_Fahrer (Driver seat position sensor) Sitzpositionsensor_Beifahrer (Passenger seat position sensor) Sitzpositionsensorserkennung_Sitzmemory_Fahrer (Driver seat position sensor memory) Sitzpositionsensorserkennung_Sitzmemory_Beifahrer (Passenger seat position sensor memory) Save, FDL code, and wait for success What I use to code out the passenger and driver side warnings when swapping seats
__________________
-2021 M2C, HS, 6MT
-AST 5100, AP Racing 9660, BMW-788M, RF-GT4, BW-TA5R, APR GT 250 Wing & Front Splitter -TMS Diffuser, TMS F80 Skid Plate, HEX Armor PPF, CAN-Checked Data Logger, RaceBox -Recaro Pole Position , 2kBody Half Cage, Pinnacle Motorsports Half Cage (On order), CAE Shifter -Remus Race + BR EL Mid |
|
Appreciate
1
Hawkdriver68.50 |
03-13-2023, 06:32 AM | #10 |
Captain
576
Rep 684
Posts |
You can run in dsc off with the seatbelt warning light on.
|
Appreciate
1
Hawkdriver68.50 |
Post Reply |
Bookmarks |
|
|