05-31-2018, 04:45 PM | #1 |
Brigadier General
1836
Rep 4,203
Posts |
VRSF HD core stepped street FMIC
So the updated VRSF Stepped Street FMIC with the hd core has arrived in my hands and I have done the unboxing. I should get to the install tomorrow or this weekend. Right now I will start off with the comparison to the previous version and factory. The DIY and comparison between the old version and stock can be found here:
http://f87.bimmerpost.com/forums/sho....php?t=1470641 Once installed I will be doing full testing of it with my current tune platform BM3 both 93 & E30 mix and post info here. So this replaces the previous core IC so it is the std going forward and priced the same as the previous version $379 The quality is wonderful and on par with the previous IC I received from them, good welds, coating, core looks good and tight...big increase over the previous version I must say. And the packing is good and protecting. And to remind everyone this in a direct drop in swap for the factory IC, no modifications are needed. Weights are Stock 7.2 Old core 17.4 New HD core 18.2 So the new core has added .8 of a pound to the overall weight Pics..... 1st pic is Tiago's side by side shot of old vs new, 2nd is the original core I installed and the rest are of the new version I will put in. More info to follow soon http://www.vr-speed.com/vrsf-interco...i-n20-n55.html sales@vr-speed.com |
06-02-2018, 09:41 AM | #4 |
Captain
196
Rep 832
Posts
Drives: 2019 G01 X3
Join Date: Oct 2007
Location: MD
|
Nice! Looking forward to the performance results.
Did you have any installation issues with the tabs like this guy did? http://f30.bimmerpost.com/forums/sho...6&postcount=61 |
Appreciate
0
|
06-02-2018, 10:22 AM | #5 | |
2095
Rep 43,350
Posts |
Quote:
Will be fixed on the next batch. |
|
06-02-2018, 11:02 AM | #6 | |
Brigadier General
1836
Rep 4,203
Posts |
Quote:
On mine I would have had to cut the one side tab off the grind a little of the other side off and some of the top for it to go up in based on my pre-measurements. Could be modified later |
|
Appreciate
0
|
06-05-2018, 01:08 PM | #7 |
BimmerPost Supporting Vendor
24185
Rep 190,777
Posts |
Looks great!
__________________
Check out our current sale by clicking on this link!
https://x-ph.com/sale/ Phone number 702-494-9435 |
Appreciate
0
|
10-16-2018, 01:49 PM | #8 |
BimmerPost Supporting Vendor
24185
Rep 190,777
Posts |
__________________
Check out our current sale by clicking on this link!
https://x-ph.com/sale/ Phone number 702-494-9435 |
Appreciate
0
|
07-30-2019, 02:33 PM | #9 |
BimmerPost Supporting Vendor
24185
Rep 190,777
Posts |
Thank you for the picture Maksim
__________________
Check out our current sale by clicking on this link!
https://x-ph.com/sale/ Phone number 702-494-9435 |
Appreciate
1
JTO245274.50 |
07-31-2019, 02:10 AM | #11 | |
Major General
5865
Rep 6,635
Posts |
Quote:
I know it was sold but I think the use case was more everyone extreme than most people. |
|
Appreciate
1
JTO245274.50 |
07-31-2019, 11:18 AM | #12 |
BimmerPost Supporting Vendor
24185
Rep 190,777
Posts |
__________________
Check out our current sale by clicking on this link!
https://x-ph.com/sale/ Phone number 702-494-9435 |
Appreciate
1
JTO245274.50 |
Post Reply |
Bookmarks |
|
|