02-11-2020, 02:39 PM | #45 | |
Lieutenant Colonel
![]() ![]() 2181
Rep 1,664
Posts |
Quote:
|
|
Appreciate
0
|
02-11-2020, 05:10 PM | #46 |
Major
![]() 1103
Rep 1,263
Posts
Drives: 20 BMW M2C 17 Mazda MX-5 RF
Join Date: Oct 2006
Location: "Get Busy Living, or Get busy Dying"
|
Yes they are set increments on the TCK plates.
Again if your looking to dial in your camber to very specific settings get GC plates, or another brand. I might eventually do that myself but for now the TCK plates maxed out give right around 3.0 Negative, more if you reverse them... 400F/700R are not that soft :-)
__________________
2005-2006 BMWCCA Boston Chapter president
2004 Mazda Rev It Up Finalist 2002-Present HPDE Instructor My 2020M2C Build: https://f87.bimmerpost.com/forums/sh....php?t=1696726 |
Appreciate
0
|
02-11-2020, 07:46 PM | #47 | |
Lieutenant Colonel
![]() ![]() 2181
Rep 1,664
Posts |
Quote:
|
|
Appreciate
1
SEAT TIME RULES1102.50 |
02-12-2020, 05:46 PM | #48 | |
Lieutenant
![]() ![]() ![]() ![]() 470
Rep 454
Posts |
Quote:
That said, Steve Ott (well known to me and McVaughan) runs our local shop and is an ex-IMSA driver as well. He was telling me about a book he was recently reading about suspension that basically says the car should be absolutely as stiff as possible, and even though that is hard to drive, its the "job of the driver" to sort out the car... and that it will only generate its max grip by allowing the tires to get to their max potential - and that would only occur with a super stiff setup. Dont ![]()
__________________
Ride: 2020 F87 M2C, 6MT Drive: Nine-Four Motorsports
Before: 2013 - 3.8L GTR, first DCT 2012 - 5.2L R8 v10, 6MT 2011 - 4.0L E92 M3, 6MT |
|
Appreciate
1
mcvaughan704.00 |
02-13-2020, 10:42 AM | #49 | |
BimmerPost Supporting Vendor
4693
Rep 2,542
Posts ![]() |
Quote:
__________________
|
|
Appreciate
1
243Racing1447.50 |
02-13-2020, 12:50 PM | #50 | |
Major General
![]() ![]() ![]() 4207
Rep 5,728
Posts
Drives: 2019 M2 Competition
Join Date: Nov 2007
Location: Orange County, CA
|
Quote:
|
|
Appreciate
0
|
02-13-2020, 01:20 PM | #51 |
BimmerPost Supporting Vendor
4693
Rep 2,542
Posts ![]() |
Yeah down force, ride height, surface conditions, all that good stuff should be accounted for when choosing spring rates. Would be interesting to see how much (I'm assuming they do) F1 teams change their rates between their different aero packages.
__________________
|
Appreciate
0
|
02-19-2020, 02:09 PM | #53 |
Major General
![]() ![]() ![]() 4207
Rep 5,728
Posts
Drives: 2019 M2 Competition
Join Date: Nov 2007
Location: Orange County, CA
|
I have put my transponder in the glove box without issue. Not a guarantee it will work but i have done it before.
|
Appreciate
0
|
02-19-2020, 02:12 PM | #54 |
Banned
1448
Rep 1,414
Posts |
|
Appreciate
0
|
02-19-2020, 03:26 PM | #55 | |
BimmerPost Supporting Vendor
4693
Rep 2,542
Posts ![]() |
Quote:
![]() ![]()
__________________
|
|
Appreciate
0
|
02-19-2020, 07:06 PM | #56 |
Major General
![]() ![]() ![]() 4207
Rep 5,728
Posts
Drives: 2019 M2 Competition
Join Date: Nov 2007
Location: Orange County, CA
|
Anyone take their comp to the quarter mile yet? I want to and plan to. It's not a proper track but kind of fun to race it down the 1/4 mile (lots of pre-run adrenaline!). I'm hoping to be in the low 12's with a tune and street tires.
|
Appreciate
0
|
02-20-2020, 10:16 AM | #57 |
BimmerPost Supporting Vendor
4693
Rep 2,542
Posts ![]() |
__________________
|
Appreciate
2
243Racing1447.50 larry.beck217.00 |
02-20-2020, 02:49 PM | #59 |
BimmerPost Supporting Vendor
4693
Rep 2,542
Posts ![]() |
__________________
|
Appreciate
0
|
02-21-2020, 01:15 PM | #61 | |
Life is on the Track, the rest is just waiting.
![]() 381
Rep 731
Posts |
Quote:
![]()
__________________
At a Point above 7,000 RPM.
|
|
Appreciate
1
243Racing1447.50 |
02-21-2020, 01:18 PM | #62 |
Banned
1448
Rep 1,414
Posts |
|
Appreciate
0
|
02-21-2020, 07:06 PM | #63 |
BimmerPost Supporting Vendor
4693
Rep 2,542
Posts ![]() |
I have used trackdecals.com - they look pretty good. Also just used one of the decal companies from googling it & never had an issue. I have also just bought some vinyl & stencils from an art store for last minute stuff - but that is kind of a pita.
Since I'm bouncing back & forth between organizations & classes right now I just had a bunch made by Signarama (think they are national) so I can remove & replace as needed. Pretty easy to make the file & they were pretty reasonable. Just keep some 3M adhesive remover handy.
__________________
|
Appreciate
0
|
02-22-2020, 01:17 AM | #65 | ||
Enlisted Member
![]() 53
Rep 44
Posts |
Quote:
Quote:
http://www.izoomgraphics.com |
||
Appreciate
2
243Racing1447.50 infinitekidM2C4206.50 |
02-22-2020, 10:13 AM | #66 |
BimmerPost Supporting Vendor
4693
Rep 2,542
Posts ![]() |
9.5" Front / 10.5" Rear - same as my now dedicated track wheels - except these are 20's instead of 18's. I figured that since I am now that guy that runs a wing on the street I need to have the bling wheels to match. Making a push to finish prettying the car up.
__________________
|
Appreciate
1
243Racing1447.50 |
Post Reply |
Bookmarks |
|
|