09-16-2022, 10:34 AM | #1 |
New Member
106
Rep 9
Posts
Drives: 2017 BMW M2
Join Date: Sep 2022
Location: Alpharetta, Georgia
|
Hey everyone, so this weekend I installed a new intercooler and charge pipe on my 2017 m2 (n55). Unfortunately though when I took off my intake during the job, the turbo inlet pipe became really loose. After investigating, I realized it broke off from the o-ring so there is no way to attach it back. This is my daily so unfortunately I will have to drive it until I can source a new one and install it. The pipe is still laying where it broke, so some air is still getting sucked past the MAF, but the car is running really rough at idle. Aside from the car running touch due to the turbo sucking in unfiltered air, can this damage the car at all? Also any recommendations on oem/aftermarket inlet pipes to replace with? Any help would be greatly appreciated.
|
09-16-2022, 11:12 AM | #2 | |
Brigadier General
2354
Rep 4,204
Posts |
Quote:
__________________
Mods: Yes.
|
|
Appreciate
1
///M TOWN21698.00 |
09-16-2022, 02:55 PM | #4 |
-
21698
Rep 8,693
Posts |
I second that ‼️
__________________
///
|
Appreciate
0
|
09-18-2022, 08:14 PM | #5 |
Where Does He Get Those Wonderful Toys?
94
Rep 290
Posts |
I’m in Alabama also and have a BNIB pure turbo V2 inlet pipe and an OEM laying around. I can meet you in prattville tomorrow. That looks about halfway between us. I’m going out of town on Tuesday and it will be awhile before I’m back.
Last edited by Boosted 1; 09-18-2022 at 08:41 PM.. |
Appreciate
0
|
09-18-2022, 09:14 PM | #6 | |
New Member
106
Rep 9
Posts
Drives: 2017 BMW M2
Join Date: Sep 2022
Location: Alpharetta, Georgia
|
Quote:
|
|
Appreciate
0
|
09-18-2022, 09:26 PM | #7 |
Where Does He Get Those Wonderful Toys?
94
Rep 290
Posts |
I think they’re around 285ish from the company. I’ll do $200 and meet you, but like I said it will have to be tomorrow probably 1300 would be the earliest I could be there.
Since you can’t PM I can give you my email and swap #’s Ches13h@aol.com |
Appreciate
0
|
09-19-2022, 03:35 PM | #8 |
Major
1198
Rep 1,243
Posts
Drives: 2017 Big Turbo BMW M2
Join Date: May 2021
Location: Tampa, FL
|
|
Appreciate
0
|
09-19-2022, 03:38 PM | #9 |
-
21698
Rep 8,693
Posts |
I am in agreement with you…
__________________
///
|
Appreciate
1
shaneguags1197.50 |
09-19-2022, 04:01 PM | #10 | ||
New Member
106
Rep 9
Posts
Drives: 2017 BMW M2
Join Date: Sep 2022
Location: Alpharetta, Georgia
|
Quote:
|
||
Appreciate
0
|
09-19-2022, 05:45 PM | #11 |
Major
1198
Rep 1,243
Posts
Drives: 2017 Big Turbo BMW M2
Join Date: May 2021
Location: Tampa, FL
|
oh haha gotcha, I misunderstood
|
Appreciate
0
|
09-20-2022, 05:37 PM | #12 | |||
-
21698
Rep 8,693
Posts |
Quote:
I have an inlet pipe if you still need one
__________________
///
|
|||
Appreciate
0
|
09-21-2022, 01:32 PM | #13 |
Captain
830
Rep 647
Posts |
Birmingham Road and Race or Mota Autohaus in Birmingham can assist should you need the support of a Pro wrench. That’s a bit of a haul from Barn Town but figured I’d mention them.
Birmingham Road and Race mitch@bhamroadandrace.com Mota Autohaus motaautohaus@gmail.com |
Appreciate
0
|
09-21-2022, 04:10 PM | #14 |
Where Does He Get Those Wonderful Toys?
94
Rep 290
Posts |
Mota is a legit installer. He’s handled both of my M’s from bushings to rod bearings, turbos to oil change! Solid guy and great work.
But again it is along way from the plains!!! |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|