01-29-2018, 10:00 AM | #45 | |
Private First Class
85
Rep 105
Posts |
Quote:
Currently running H&R springs, but that will most likely change soon. I will definitely get a pic of the inner clearance on the front, as well as rear as soon as I can get it on the lift. I will be aligning the car some time toward the end of the week; I want to get some miles on the springs first. |
|
Appreciate
0
|
02-04-2018, 11:47 PM | #46 |
Lieutenant
150
Rep 485
Posts |
BBS FI-R’s with 255/35/19 and 275/35/19 PS4 working great here on MP coils. I raised the front a little (had a minor rub on hard bumps even on stock wheels at lowest setting) and got the tiniest rub over a known hard bump but otherwise even with a passenger not rubbing.
I’d say this is a doable config, once “height adjusted.” Loving the hell out of the added traction too. |
Appreciate
0
|
02-05-2018, 06:52 AM | #47 |
Old Guy
25
Rep 89
Posts
Drives: 2018 M2 LCI, 2019 X3
Join Date: May 2014
Location: Niceville Florida
|
Z-Performance
Wheels: Z-Performance ZP2.1
Front: 20x9.5 ET 20 with P245/30 - 20 Michelin P4S Rear: 20x11 ET 40 with P295/25 - 20 Michelin PSS Suspension: Stock Comments: No Rub, no spacers needed. Just put them on, ride is not that different but I have pretty good roads here. |
Appreciate
1
CSBM52722.50 |
02-05-2018, 08:21 AM | #48 | |
Meh
926
Rep 781
Posts
Drives: M3CS & Cayman S
Join Date: Jul 2008
Location: Cali
|
Quote:
edit: nvm didn't see ps4. added to list |
|
Appreciate
0
|
03-11-2018, 08:52 PM | #49 | ||||
Major
609
Rep 1,124
Posts |
Quote:
__________________
Current: 2017 ///M2 manual 2004 E85 Z-4 manual
|
||||
Appreciate
0
|
03-12-2018, 10:37 AM | #50 | |||||
Captain
625
Rep 796
Posts |
Quote:
|
|||||
Appreciate
1
rich8566608.50 |
03-18-2018, 12:32 PM | #51 | |
Captain
433
Rep 753
Posts |
Is that on stock suspension? I wonder if 19x9.5et30 square would work with 265/35 all around and a 8-10mm spacer out back?
Quote:
|
|
Appreciate
1
lp1645.50 |
04-03-2018, 06:09 AM | #52 |
Enlisted Member
57
Rep 39
Posts |
Anyone else run 19x9.5 and 19x10.5 wheels on the stock (245 front/265 rear) tyres? Any issues with this?
I would like to get a new set of wheels but since my tyres are nearly brand new I'd like to keep using them.
__________________
|
Appreciate
0
|
04-13-2018, 02:52 PM | #54 |
Lieutenant
283
Rep 399
Posts
Drives: 2017 BMW M2 6MT
Join Date: Apr 2016
Location: Toronto
|
you meant to type 285/30/19 out back right?
__________________
'17 BMW M2 LBB 6MT MPE
'13 BMW 335i Estoril Blue - sold |
Appreciate
0
|
04-13-2018, 03:00 PM | #55 |
Meh
926
Rep 781
Posts
Drives: M3CS & Cayman S
Join Date: Jul 2008
Location: Cali
|
no 285/35R19 is on there
|
Appreciate
0
|
04-16-2018, 08:44 AM | #56 |
Private
43
Rep 56
Posts |
Signature wheels SV501
www.signaturewheel.com 9,5x19 ET25 Front (on pictures ET22) 10,5x19 ET40 Rear F 265/30 Toyo R888R R 295/30 Toyo R888R Ohlins Road & Track chassi. (With Ohlins in front, ET needs to be 22-23. 25 will have the tires yet so gently touching the front springs) No rubbing with stock camber. No rubbing with following camber: F -3,3 ° R -2,0 ° |
Appreciate
3
|
04-21-2018, 07:10 PM | #57 |
Lieutenant
518
Rep 582
Posts |
Wheels: Apex SM10 18x10 et 33 square. 12mm spacer in front.
Front: SM10 18x10 et 33 with 275/35 - 18 NT01 Rear: SM10 18x10 et 33 with 275/35 - 18 NT01 Suspension: Bilstein PSS10 lowered ride height. Ground Control camber plates running -3.2 camber Comments: No Rub at current setup |
Appreciate
0
|
08-16-2018, 11:16 PM | #58 |
Registered
29
Rep 4
Posts |
DSC00034-Edit by Dü Werke, on Flickr
DSC00005 by Dü Werke, on Flickr DSC00002 by Dü Werke, on Flickr KW V3 GC camber plates -3 degrees F+R Rotiform WGR 18x9.5 square (few MMs needed to be shaved off side of calipers) 265/35r18 Yokohama Advan A052 square Front fenders rolled/pulled/bumper tab removed (-3.5 F camber would alleviate most of these requirements) |
Appreciate
1
QM287.00 |
09-18-2018, 07:41 PM | #61 |
Registered
37
Rep 3
Posts |
Does Anybody kow if the M235i racing wheels and tires have a correct fitment with the M2? If my calculations are right the fronts could rub without a widebody kit.
|
Appreciate
0
|
05-01-2019, 08:43 PM | #62 | |
Enlisted Member
56
Rep 46
Posts |
wonder if rear ll be too aggressive
Quote:
hi guys, i m currently looking into a set of special edition prodrive gc05n with the following spec 19x9 ET30 19x10 ET25 my car is stock and i m not planing on lowing it, no track use only occasional hill climb will i get away with the rear rubbing from poking too much out? thx in advance, ed~ |
|
Appreciate
0
|
05-02-2019, 10:25 AM | #63 |
Major
566
Rep 1,092
Posts |
The front is pretty much stock, the rear pokes out 15mm farther.
People regularly run 12mm spacers all around so another 3mm should be doable. You should stick to stock tire sizes and be prepared to add a bit of negative camber and you should be fine. Oh, and get a 15mm spacer for the fronts so it looks even. |
Appreciate
1
bunnyhive55.50 |
05-03-2019, 09:39 PM | #64 |
Private First Class
234
Rep 127
Posts
Drives: 2017 M2 Mineral Gray
Join Date: Jan 2019
Location: GA
|
Wheels: Vorsteiner VFF-106 Carbon Graphite 19x9.5 et22 19x10.5 et34
Tires: Michelin MP4S 265/30F 295/30R Suspension: KW v3 & Vorshlag camber plates about .75" drop for now -1.9 & -1.8 camber front -2.6 & -2.4 camber rear No rubbing so far with only me in the car, we'll see how it goes once the suspension settles in. I wasn't sure if this would fit, but thanks to the installers and a good alignment it seems to be working well. I'm glad I went with my gut (and info from others with similar setups) that this would fit since I don't think anyone else is running this exact setup. |
Appreciate
2
VisualEcho6636.50 Rundskop148.00 |
07-28-2019, 08:51 PM | #65 |
Major
1104
Rep 1,083
Posts |
Signature SV104
Meaty Setup:
19x9.5 ET23 front and 19x10.5 ET40 rear F8x stock 255/35/19 and 275/35/19 Recommended Setup: 19x9.5 ET23 front and 19x10.5 ET40 rear 265/30/19 front and 295/30/19 *Signature SV104 shown Note our inner wheel barrels give those massive M2C calipers more breathing room. |
Appreciate
1
Jarran10.50 |
03-23-2020, 08:23 PM | #66 |
New Member
0
Rep 6
Posts |
Hi all,
Looking to test the waters on the following wheel specs 19x9.5 +33 F (stock tire size) 19x10 +25 R (stock tire size) Not lowered yet but want to ensure that there is no rubbing issues before committing to coils. let me know what you think |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|